Çözüldü Realme 8 (RMX3085) IMEI Repair

[elcin235]

Bu islemi Pandora Tolla yapdim
Lazim olan yazilim https://ssurl.pro/ZfYOR

Selected model: REALME RMX3085(Realme 8)
Operation: Repair
Software version: 5.0

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM58 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0813
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM58 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x88D5DB92, 0x79454E74, 0x43E6EA7B, 0x919F497E
Get Chip ID... [MT6785]
Get SOC ID... [9E5C979534AD7A62EB4D955E6ED5A635C03121A24B59818F3CB1F57BB0DBE3F3]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM8V9001JM-B813 (0600)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM8V9001JM-B813
UFS_FWVER : 0600
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : oplus_mssi_64_cn
Product Name : sys_oplus_mssi_64_cn
Product Device : oplus_mssi_64_cn
Product Board : oppo6785
Board Platform : MT6785
Build ID : RP1A.200720.011
Build Date : Thu Sep 16 18:02:54 CST 2021
Display ID : RP1A.200720.011 release-keys
Security Patch : 2021-09-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1619430602288
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Repairing IMEI...
IMEI 1: 358750061******
IMEI 2: 358750061*******
Write IMEI [NVDATA]... OK
Load partiton for patching... OK
Save patched partiton... OK
Unlock bootloader... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
If your phone after repair keeps rebooting - use wipe data option.Selected model: OPPO CPH1909 (Oppo A5s)
Operation: Repair
Software version: 3.5

Host Power Off... OK
Switch virtual port to NONE... OK
Connect Type-C to HUB... OK
Host Power On... OK
Connect phone to BOX in BROM/PRELOADER Mode
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM58 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Force switch to BROM... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Wait for device... OK
Read usbhost speed... HIGH
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 0813
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Get sec config... OK [000000E5]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Driver: [MediaTek Inc.,wdm_usb,MediaTek USB Port_V1632,usb2ser.sys,3.0.1504.0]
Device found at COM58 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 0813
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6785]
Library Version [2]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Reopen port for libver2... OK
Get ME ID... OK
ME_ID = 0x88D5DB92, 0x79454E74, 0x43E6EA7B, 0x919F497E
Get Chip ID... [MT6785]
Get SOC ID... [9E5C979534AD7A62EB4D955E6ED5A635C03121A24B59818F3CB1F57BB0DBE3F3]
Get sec config... OK [000000E0]
Load DownloadAgent... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Wait for answer from bootloader... OK
Send SYNC signal... OK
Setup device enviroment... OK
Setup device parametres... OK
Receive DA SYNC signal... OK
Set DA parametres... OK
Get device connection agent... [BROM]
Get device info... OK
UFS CID (FW VER): KM8V9001JM-B813 (0600)
Load EMI from phone... OK
Parse EMI config... OK
Init EXT RAM... OK
Send 2nd DA... OK
Get device info... OK
UFS INFO:
UFS_CID : KM8V9001JM-B813
UFS_FWVER : 0600
BLOCK_SIZE: 0x0000001000 (4.00Kb)
UFS_LU0 : 0x0000400000 (4.00Mb)
UFS_LU1 : 0x0000400000 (4.00Mb)
UFS_LU2 : 0x1DCB000000 (119.17Gb)
RAM INFO:
INT_SRAM: 0x0000080000 (512.00Kb)
EXT_RAM : 0x0200000000 (8.00Gb)
Check USB status... USB_HIGH_SPEED
Read partitions info from phone... OK
Check A/B state... OK
Read product info... OK
Product Brand : alps
Product Manufacturer : alps
Product Model : oplus_mssi_64_cn
Product Name : sys_oplus_mssi_64_cn
Product Device : oplus_mssi_64_cn
Product Board : oppo6785
Board Platform : MT6785
Build ID : RP1A.200720.011
Build Date : Thu Sep 16 18:02:54 CST 2021
Display ID : RP1A.200720.011 release-keys
Security Patch : 2021-09-05
Version SDK : 30
Version Release : 11
Version Codename : REL
Firmware Version : 1619430602288
Read partition "nvdata"... OK
Read partition "nvram"... OK
Read NVDATA files... OK
Read NVRAM files... OK
Repairing IMEI...
IMEI 1: 358750061*******
IMEI 2: 358750061*******
Write IMEI [NVDATA]... OK
Load partiton for patching... OK
Save patched partiton... OK
Unlock bootloader... OK
Write IMEI [NVRAM]... OK
Write partition "nvdata"... OK
Write partition "nvram"... OK
Repair Security done!
If your phone after repair keeps rebooting - use wipe data option.