Çözüldü Samsung Galaxy S8 Plus SM-G955U U8 SIM Unlock

[silivriserdar]

Merhaba GSM Turkey Üyeleri bu paylaşacağım konuda Samsung Galaxy S8 Plus SM-G955U cihazına ait SIM unlock başarı raporunu paylaşacağım. Ben bu işlemi Z3X Box Samsung Tool ile yaptım bu araç ücretli bir araçtır.

Lütfen konu altına yorum yaparken Teşekkürler, Elinize sağlık, süper, sağol, helal olsun gibi kelimeler yazıp konuları kirletmeyelim. Herkes aradığını bu mesajlar yüzünden bulamıyor. Altta beğen butonuna basmanız yeterlidir. Konu ile ilgili sorununuzu veya çözümünüz varsa yorum yapın. Konu ile alakasız cevaplar silinecektir. ​

​

 UNLOCK INSTRUCTIONS:
Unlocking with original MSL code:
Warning! Knox warranty must be active (0x00)!
If you have it voided (0x01(void)), then you can't unlock this phone with MSL.
1. Phone must be powered on.
2. Type *#0808# and select 'DM+ACM+ADB'.
3. Run dialer and type *#0*# (service mode will appear).
4. Connect the phone to USB cable, choose correct COM port in port settings.
5. Press 'Unlock' button.
6. Paste MSL code in new opened window and press 'OK'.

Unlocking TMB using sever:
1. Power on the phone.
2. Tap 7 times on 'Build number' in 'Settings'-'About phone'-'Software information'
to enable 'Developer options',
go to 'Settings'-'Developer options' and enable 'USB debugging'.
3. Connect the phone to PC with USB cable, install drivers if needed.
4. Select device in ADB settings.
5. Press 'Unlock TMB via server' button, write your login and password in window if it will appear.
(Login and password will be saved as default after first input and can be changed in settings.)

Unlocking SPR using sever:
1. Insert not SPR card to the phone and power it on.
2. Tap 7 times on 'Build number' in 'Settings'-'About phone'-'Software information'
to enable 'Developer options',
go to 'Settings'-'Developer options' and enable 'USB debugging'.
3. Connect the phone to PC with USB cable, install drivers if needed.
4. Select device in ADB settings.
5. Press 'Unlock...' button, select 'Unlock SPR via Server', 
write your login and password in window if it will appear. 
(Login and password will be saved as default after first input and can be changed in settings.)

Reading codes using sever:
1. Power on the phone.
2. Tap 7 times on 'Build number' in 'Settings'-'About phone'-'Software information'
to enable 'Developer options',
go to 'Settings'-'Developer options' and enable 'USB debugging'.
3. Connect the phone to PC with USB cable, install drivers if needed.
4. Select device in ADB settings.
5. Press 'Read Codes via server' button, write your login and password in window if it will appear.
(Login and password will be saved as default after first input and can be changed in settings.) 

Operation: Read Codes via Server
Selected model: SM-G955U
Selected port: COM3 SAMSUNG Mobile USB Serial Port 
Software version: 44.11

Checking Login and Password... OK
Balance: 25 crd.
You have 25 credit(s) left. This operation takes 5 credits. Continue? Yes
Waiting for device to become ready... OK
Reading phone info...
Model: SM-G955U
Android version: 9
PDA version: G955USQS8DTJ1
CSC version: G955UOYN8DTJ1
Phone version: G955USQS8DTJ1
Product code: SM-G955UZKAATT
CSC country code: USA
CSC sales code: ATT
Carrier ID: ATT
Phone SN: R38J40QQXFP
IMEI: 
HW version: REV1.0
RF cal date: 2017.04.26
Chip name: MSM8998
Modem board: MSM8998
Security patch: 2020-10-01
Boot Warranty bit: 0
SIM State: ABSENT
Searching Samsung diag port... detected COM3
Initialization zTool... OK
Running zTool, please wait... OK
Executing... OK
Searching Ramdump interface... COM5 detected
Reading data from phone... OK
Calculating... OK
Searching server... OK
Waiting for server answer... OK
Freeze code: 17531748
NET lock: 51631647
SUB lock: 00000000
SP lock: 00000000
CP lock: 00000000
For check lock status: *#7465625#
Done with Samsung Tool PRO v.44.11 [SM-G955U,Read Codes via Server]